GP 25 How to Setup Ethernet Crossover Cable for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
Purpose
To connect and then configure the PWS to communicate with a device via a ethernet crossover cable (600T02252).
Procedure
WARNING: Switch off the electricity to the machine GP 10. Disconnect the power cord from the customer supply while performing tasks that do not need electricity. Electricity can cause death or injury. Moving parts can cause injury.
1. Print a configuration report, GP 14.
2. Ensure that Windows firewall and wireless network connectivity on the PWS are turned off.
3. Record the IP address and Subnet Mask of the PWS.
CAUTION: Before changing the value of a setting ensure the original value is recorded. All the original values will need to be restored to the PWS at the end of the procedure.
a. Open a command window on the PWS:
• Select Start and in the Search box above the Start button, type CMD, then press Enter.
NOTE: If the Windows key is enabled (the key located in the lower left corner with the Microsoft logo), hold the Windows key down, press R and release both keys to open the Command window.
b. Type ipconfig at the command prompt, then record the Local Area Connection: IPv4 Address and Subnet Mask.
4. Configure the LAN connection of the PWS to enable communication with the device. Go to the relevant procedure:
• Windows 7.
• Windows 10.
Windows 7
Perform the steps that follow:
1. Select the Windows Start button, then Control Panel, then Network and Sharing Centre.
2. From the left pane, select Change adapter settings.
3. Right-click on the Local Area Connection icon. Select Properties. The Local Area Connection Properties window will open.
4. Select Internet Protocol Version 4 (TCP/IPv4). Select Properties. The Internet Protocol Version 4 (TCP/IPv4) Properties window will open.
5. Double-click the entry Internet Protocol Version 4 (TCP/IPv4).
6. Select Use the following IP address, then enter the IP address and subnet mask. Refer to the configuration report then:
• Set the IP address of the laptop one number higher than the device. For example, if the IP address of the device is 192.168.196.112, set the IP address of the laptop to 192.168.196.113.
• Set the Subnet mask of the laptop to the same as the Subnet mask of the device.
7. Click on OK to close the properties dialog box, then OK to close the second properties dialog box.
8. Close the Local Area Connection Status dialog box.
9. Connect the ethernet crossover cable to the device, then continue with your procedure.
Windows 10
Perform the steps that follow:
1. Select the Windows Start button, then select Settings.
2. Select Network & Internet.
3. Under Related settings select Network and Sharing Center, then from the task list on the left of the screen select Change adapter settings.
4. Right click on Local Area Connection (Ethernet), then select Properties.
5. Select Internet Protocol Version 4(TCP/IPv4), then select Properties. The Internet Protocol Version 4 (TCP/IPv4) Properties window will open.
6. Select Use the following IP address, then enter the IP address and subnet mask.
Refer to the configuration report then:
• Set the IP address of the laptop one number higher than the device. For example, if the IP address of the device is 192.168.196.112, set the IP address of the laptop to 192.168.196.113.
• Set the Subnet mask of the laptop to the same as the Subnet mask of the device.
7. Select OK to close the properties dialog box, then OK to close the second properties dialog box.
8. Close the Local Area Connection Status dialog box.
9. Connect the ethernet crossover cable to the device, then continue with your procedure.
**This procedure is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
To connect and then configure the PWS to communicate with a device via a ethernet crossover cable (600T02252).
Procedure
WARNING: Switch off the electricity to the machine GP 10. Disconnect the power cord from the customer supply while performing tasks that do not need electricity. Electricity can cause death or injury. Moving parts can cause injury.
1. Print a configuration report, GP 14.
2. Ensure that Windows firewall and wireless network connectivity on the PWS are turned off.
3. Record the IP address and Subnet Mask of the PWS.
CAUTION: Before changing the value of a setting ensure the original value is recorded. All the original values will need to be restored to the PWS at the end of the procedure.
a. Open a command window on the PWS:
• Select Start and in the Search box above the Start button, type CMD, then press Enter.
NOTE: If the Windows key is enabled (the key located in the lower left corner with the Microsoft logo), hold the Windows key down, press R and release both keys to open the Command window.
b. Type ipconfig at the command prompt, then record the Local Area Connection: IPv4 Address and Subnet Mask.
4. Configure the LAN connection of the PWS to enable communication with the device. Go to the relevant procedure:
• Windows 7.
• Windows 10.
Windows 7
Perform the steps that follow:
1. Select the Windows Start button, then Control Panel, then Network and Sharing Centre.
2. From the left pane, select Change adapter settings.
3. Right-click on the Local Area Connection icon. Select Properties. The Local Area Connection Properties window will open.
4. Select Internet Protocol Version 4 (TCP/IPv4). Select Properties. The Internet Protocol Version 4 (TCP/IPv4) Properties window will open.
5. Double-click the entry Internet Protocol Version 4 (TCP/IPv4).
6. Select Use the following IP address, then enter the IP address and subnet mask. Refer to the configuration report then:
• Set the IP address of the laptop one number higher than the device. For example, if the IP address of the device is 192.168.196.112, set the IP address of the laptop to 192.168.196.113.
• Set the Subnet mask of the laptop to the same as the Subnet mask of the device.
7. Click on OK to close the properties dialog box, then OK to close the second properties dialog box.
8. Close the Local Area Connection Status dialog box.
9. Connect the ethernet crossover cable to the device, then continue with your procedure.
Windows 10
Perform the steps that follow:
1. Select the Windows Start button, then select Settings.
2. Select Network & Internet.
3. Under Related settings select Network and Sharing Center, then from the task list on the left of the screen select Change adapter settings.
4. Right click on Local Area Connection (Ethernet), then select Properties.
5. Select Internet Protocol Version 4(TCP/IPv4), then select Properties. The Internet Protocol Version 4 (TCP/IPv4) Properties window will open.
6. Select Use the following IP address, then enter the IP address and subnet mask.
Refer to the configuration report then:
• Set the IP address of the laptop one number higher than the device. For example, if the IP address of the device is 192.168.196.112, set the IP address of the laptop to 192.168.196.113.
• Set the Subnet mask of the laptop to the same as the Subnet mask of the device.
7. Select OK to close the properties dialog box, then OK to close the second properties dialog box.
8. Close the Local Area Connection Status dialog box.
9. Connect the ethernet crossover cable to the device, then continue with your procedure.
**This procedure is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782