How to Fix 012-132B Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
012-132B Entrance Sensor On Jam RAP
BSD-ON: BSD 13.7 Office Finisher LX Transportation
Procedure
NOTE: Ensure the correct RAP is performed, refer to the 012-132 Entrance Sensor On Jam Entry RAP.
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
1. Enter dC330 code 012-100. Actuate the finisher transport entrance sensor, PL 13.35 Item 10. The display changes. If YES, go to 9. If NO, go to 2.
2. Check the wiring between J8868 pin 2 and P/J8988 pin 2 for an open or short circuit, or a loose or damaged connector. The wiring is good. If YES, go to 4. If NO, go to 3.
3. Reconnect or repair as necessary.
4. Measure the voltage between P/J8988 pins 1 and 3 on the finisher PWB. The voltage is approximately +5VDC. If YES, go to 6. If NO, go to 5.
5. Install a new finisher PWB, PL 13.45 Item 2.
6. Measure the voltage between P/J8988 pin 2 on the finisher PWB and ground. Actuate the finisher entrance sensor. The voltage changes. If YES, go to 8. If NO, go to 7.
7. Install a new finisher transport entrance sensor, PL 13.35 Item 10.
8. Install a new finisher PWB, PL 13.45 Item 2.
9. Enter dC330 code 012-038. The transport motor runs. If YES, go to 15. If NO, go to 10.
10. Check the wiring between P/J8879 on the transport motor and P/J8983 on the finisher PWB for an open or short circuit, or a loose or damaged connector. The wiring is good. If YES, go to 12. If NO, go to 11.
11. Reconnect or repair as necessary.
12. Measure the resistance of the transport motor between P/J8879 pins 1, 2, 5 and 6. The resistance is approximately 20 Ohms. If YES, go to 14. If NO, go to 13.
13. Install a new transport motor, PL 13.08 Item 13.
14. Install a new finisher PWB, PL 13.45 Item 2. If the fault persists, install a new transport motor, PL 13.08 Item 13.
15. Check the components that follow:
• The entrance roller, paddle shaft and eject belt, PL 13.29 for wear, damage or contamination.
• The finisher entrance sensor and transport motor circuits for an intermittent condition.
If the fault persists, install a new finisher PWB, PL 13.45 Item 2.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON: BSD 13.7 Office Finisher LX Transportation
Procedure
NOTE: Ensure the correct RAP is performed, refer to the 012-132 Entrance Sensor On Jam Entry RAP.
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
1. Enter dC330 code 012-100. Actuate the finisher transport entrance sensor, PL 13.35 Item 10. The display changes. If YES, go to 9. If NO, go to 2.
2. Check the wiring between J8868 pin 2 and P/J8988 pin 2 for an open or short circuit, or a loose or damaged connector. The wiring is good. If YES, go to 4. If NO, go to 3.
3. Reconnect or repair as necessary.
4. Measure the voltage between P/J8988 pins 1 and 3 on the finisher PWB. The voltage is approximately +5VDC. If YES, go to 6. If NO, go to 5.
5. Install a new finisher PWB, PL 13.45 Item 2.
6. Measure the voltage between P/J8988 pin 2 on the finisher PWB and ground. Actuate the finisher entrance sensor. The voltage changes. If YES, go to 8. If NO, go to 7.
7. Install a new finisher transport entrance sensor, PL 13.35 Item 10.
8. Install a new finisher PWB, PL 13.45 Item 2.
9. Enter dC330 code 012-038. The transport motor runs. If YES, go to 15. If NO, go to 10.
10. Check the wiring between P/J8879 on the transport motor and P/J8983 on the finisher PWB for an open or short circuit, or a loose or damaged connector. The wiring is good. If YES, go to 12. If NO, go to 11.
11. Reconnect or repair as necessary.
12. Measure the resistance of the transport motor between P/J8879 pins 1, 2, 5 and 6. The resistance is approximately 20 Ohms. If YES, go to 14. If NO, go to 13.
13. Install a new transport motor, PL 13.08 Item 13.
14. Install a new finisher PWB, PL 13.45 Item 2. If the fault persists, install a new transport motor, PL 13.08 Item 13.
15. Check the components that follow:
• The entrance roller, paddle shaft and eject belt, PL 13.29 for wear, damage or contamination.
• The finisher entrance sensor and transport motor circuits for an intermittent condition.
If the fault persists, install a new finisher PWB, PL 13.45 Item 2.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782