How to Fix 012-151A Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
012-151A Compiler Exit Sensor Off Jam RAP
BSD-ON: BSD 12.3 Integrated Office Finisher Transportation
Initial Actions
NOTE: Ensure the correct RAP is performed, refer to the 012-151 Compiler Exit Sensor Off Jam Entry RAP
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Check the compiler exit sensor, PL 12.12 Item 16 is correctly installed and free from foreign objects and that the actuator is not binding.
• Switch off, then switch on the machine, GP 10.
Procedure
1. Check the specifications of paper, GP 15. Paper is in specification. If YES, go to 3. If NO, go to 2.
2. Load paper that is in specification.
3. Check the condition of the paper. The paper is in normal condition without any problem that causes the paper to be bent or caught. If YES, go to 5. If NO, go to 4.
4. Resolve any problem that causes the paper to be bent or caught.
5. Check the transport path for a foreign object, deformed part or paper dust. The transport path is good. If YES, go to 7. If NO, go to 6.
6. Repair the deformed part(s) or remove the foreign object(s) and paper dust.
7. Check the exit roll, PL 12.11 Item 10 for wear, deterioration or paper dust. The exit roll is good. If YES, go to 9. If NO, go to 8.
8. Remove the paper dust or install a new exit roll, PL 12.11 Item 10.
9. Check the drive mechanism to the exit roll for a deformed, broken part, and/or belt damage. The drive mechanism is free of defects. If YES, go to 11. If NO, go to 10.
10. Repair defects or damage to the drive mechanism. Install new components as necessary, PL 12.11.
11. Enter dC330 code 012-150. Actuate the compiler exit sensor. The display changes. If YES, go to 21. If NO, go to 12.
12. Check the connections of P/J8709 and P/J8728. The connectors are good. If YES, go to 14. If NO, go to 13.
13. Secure the connections.
14. Check for an open or short circuit between P/J8709 and P/J8728. The wiring is good. If YES, go to 16. If NO, go to 15.
15. Repair the open or short circuit.
16. Measure the voltage between the finisher PWB P/J8709 pin 3 (+) and ground (-). The voltage is approximately +5VDC. If YES, go to 18. If NO, go to 17.
17. Check the +5VDC circuit.
18. Measure the voltage between the finisher PWB P/J8709 pin 2 (+) and ground (-). Actuate the compiler exit sensor. The voltage changes. If YES, go to 20. If NO, go to 19.
19. Install a new compiler exit sensor, PL 12.12 Item 16.
20. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
21. Enter dC330 code 012-095. The finisher transport motor runs. If YES, go to 29. If NO, go to 22.
22. Check the connections of P/J8706 and P/J8739. The connectors are good. If YES, go to 24. If NO, go to 23.
23. Secure the connections.
24. Check for an open or short circuit between P/J8706 and P/J8739. The wiring is good. If YES, go to 26. If NO, go to 25.
25. Repair the open or short circuit.
26. Measure the voltage between the finisher PWB P/J8706 pin 5 (+) and ground (-), and P/J8706 pin 7 (+) and ground (-). Each voltage is approximately +24VDC. If YES, go to 28. If NO, go to 27.
27. Check the +24VDC circuit.
28. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new components as necessary:
• Finisher transport motor, PL 12.12 Item 17.
• Finisher PWB, PL 12.14 Item 1.
29. Enter dC330 code 012-013. The sub paddle solenoid energizes and the sub paddle shaft assembly moves vertically. If YES, go to 41. If NO, go to 30.
30. Check the sub paddle mechanism for damage The sub paddle mechanism is good. If YES, go to 32. If NO, go to 31.
31. Repair defects, or install new components as necessary, PL 12.10.
32. Check the connections of P/J8705 and P/J8734. The connectors are good. If YES, go to 34. If NO, go to 33.
33. Secure the connections.
34. Check for an open or short circuit between P/J8705 and P/J8734. The wiring is good. If YES, go to 36. If NO, go to 35.
35. Repair the open or short circuit.
36. Measure the voltage between the finisher PWB P/J8705 pin 1 (+) and ground (-). The voltage is approximately +24VDC. If YES, go to 38. If NO, go to 37.
37. Check the +24VDC circuit. Refer to Chapter 7 Wiring Data. If the circuit is good, install a new finisher PWB, PL 12.14 Item 1.
38. Enter dC330 code 012-013. Measure the voltage between the finisher PWB P/J8705 pin 2 (+) and ground (-). The voltage changes. If YES, go to 40. If NO, go to 39.
39. Install a new finisher PWB, PL 12.14 Item 1.
40. Install a new sub paddle solenoid, PL 12.10 Item 27.
41. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON: BSD 12.3 Integrated Office Finisher Transportation
Initial Actions
NOTE: Ensure the correct RAP is performed, refer to the 012-151 Compiler Exit Sensor Off Jam Entry RAP
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Check the compiler exit sensor, PL 12.12 Item 16 is correctly installed and free from foreign objects and that the actuator is not binding.
• Switch off, then switch on the machine, GP 10.
Procedure
1. Check the specifications of paper, GP 15. Paper is in specification. If YES, go to 3. If NO, go to 2.
2. Load paper that is in specification.
3. Check the condition of the paper. The paper is in normal condition without any problem that causes the paper to be bent or caught. If YES, go to 5. If NO, go to 4.
4. Resolve any problem that causes the paper to be bent or caught.
5. Check the transport path for a foreign object, deformed part or paper dust. The transport path is good. If YES, go to 7. If NO, go to 6.
6. Repair the deformed part(s) or remove the foreign object(s) and paper dust.
7. Check the exit roll, PL 12.11 Item 10 for wear, deterioration or paper dust. The exit roll is good. If YES, go to 9. If NO, go to 8.
8. Remove the paper dust or install a new exit roll, PL 12.11 Item 10.
9. Check the drive mechanism to the exit roll for a deformed, broken part, and/or belt damage. The drive mechanism is free of defects. If YES, go to 11. If NO, go to 10.
10. Repair defects or damage to the drive mechanism. Install new components as necessary, PL 12.11.
11. Enter dC330 code 012-150. Actuate the compiler exit sensor. The display changes. If YES, go to 21. If NO, go to 12.
12. Check the connections of P/J8709 and P/J8728. The connectors are good. If YES, go to 14. If NO, go to 13.
13. Secure the connections.
14. Check for an open or short circuit between P/J8709 and P/J8728. The wiring is good. If YES, go to 16. If NO, go to 15.
15. Repair the open or short circuit.
16. Measure the voltage between the finisher PWB P/J8709 pin 3 (+) and ground (-). The voltage is approximately +5VDC. If YES, go to 18. If NO, go to 17.
17. Check the +5VDC circuit.
18. Measure the voltage between the finisher PWB P/J8709 pin 2 (+) and ground (-). Actuate the compiler exit sensor. The voltage changes. If YES, go to 20. If NO, go to 19.
19. Install a new compiler exit sensor, PL 12.12 Item 16.
20. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
21. Enter dC330 code 012-095. The finisher transport motor runs. If YES, go to 29. If NO, go to 22.
22. Check the connections of P/J8706 and P/J8739. The connectors are good. If YES, go to 24. If NO, go to 23.
23. Secure the connections.
24. Check for an open or short circuit between P/J8706 and P/J8739. The wiring is good. If YES, go to 26. If NO, go to 25.
25. Repair the open or short circuit.
26. Measure the voltage between the finisher PWB P/J8706 pin 5 (+) and ground (-), and P/J8706 pin 7 (+) and ground (-). Each voltage is approximately +24VDC. If YES, go to 28. If NO, go to 27.
27. Check the +24VDC circuit.
28. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new components as necessary:
• Finisher transport motor, PL 12.12 Item 17.
• Finisher PWB, PL 12.14 Item 1.
29. Enter dC330 code 012-013. The sub paddle solenoid energizes and the sub paddle shaft assembly moves vertically. If YES, go to 41. If NO, go to 30.
30. Check the sub paddle mechanism for damage The sub paddle mechanism is good. If YES, go to 32. If NO, go to 31.
31. Repair defects, or install new components as necessary, PL 12.10.
32. Check the connections of P/J8705 and P/J8734. The connectors are good. If YES, go to 34. If NO, go to 33.
33. Secure the connections.
34. Check for an open or short circuit between P/J8705 and P/J8734. The wiring is good. If YES, go to 36. If NO, go to 35.
35. Repair the open or short circuit.
36. Measure the voltage between the finisher PWB P/J8705 pin 1 (+) and ground (-). The voltage is approximately +24VDC. If YES, go to 38. If NO, go to 37.
37. Check the +24VDC circuit. Refer to Chapter 7 Wiring Data. If the circuit is good, install a new finisher PWB, PL 12.14 Item 1.
38. Enter dC330 code 012-013. Measure the voltage between the finisher PWB P/J8705 pin 2 (+) and ground (-). The voltage changes. If YES, go to 40. If NO, go to 39.
39. Install a new finisher PWB, PL 12.14 Item 1.
40. Install a new sub paddle solenoid, PL 12.10 Item 27.
41. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782