How to Fix 012-224A 012-263A Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
012-224A, 012-263A Rear Tamper Home Sensor Fail RAP
BSD-ON: BSD 12.4 Integrated Office Finisher Tamping and Offset
Initial Actions
NOTE: Ensure the correct RAP is performed, refer to the 012-224, 012-263 Rear Tamper Home Sensor Fail Entry RAP.
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Check the rear tamper home sensor, PL 12.25 Item 9 is correctly installed and has no foreign object and that the actuator is not broken.
• Switch off, then switch on the machine, GP 10.
Procedure
1. Check the rear tamper for any foreign object, deformation and binding that prevents it from moving. The rear tamper is good. If YES, go to 3. If NO, go to 2.
2. Repair the deformation and remove the foreign object(s) and the binding. Install new components as necessary, PL 12.26.
3. Check the drive mechanism to the rear tamper for a deformed or broken part and not-seated gears. The drive mechanism is good. If YES, go to 5. If NO, go to 4.
4. Repair the rear tamper drive mechanism. Install new components as necessary, PL 12.26.
5. Enter dC330 code 012-221. Manually move the rear tamper to actuate the front tamper home sensor. The display of changes. If YES, go to 15. If NO, go to 6.
6. Check the connections of P/J8700 and P/J8726. The connectors are good. If YES, go to 8. If NO, go to 7.
7. Secure the connections.
8. Check for an open or short circuit between P/J8700 and P/J8726. The wiring is good. If YES, go to 10. If NO, go to 9.
9. Repair the open wire or short circuit.
10. Measure the voltage between the finisher PWB P/J8700 pin 12 (+) and ground (-). The voltage is approximately +5VDC. If YES, go to 12. If NO, go to 11.
11. Check the +5VDC circuit.
12. Measure the voltage between the finisher PWB P/J8700 pin 11 (+) and ground (-). Manually move the rear tamper to actuate the front tamper home sensor. The voltage changes. If YES, go to 14. If NO, go to 13.
13. Install a new rear tamper home sensor, PL 12.25 Item 9.
14. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
15. Enter dC330 code 012-026 and 012-029 alternately. The rear tamper motor runs. If YES, go to 23. If NO, go to 16.
16. Check the connections of P/J8710 and J8737. The connectors are good. If YES, go to 18. If NO, go to 17.
17. Secure the connections.
18. Check for an open wire or short circuit between P/J8710 and J8737. The wiring is good. If YES, go to 20. If NO, go to 19.
19. Repair the open or short circuit.
20. Measure the voltage between the finisher PWB P/J8710 pin 1 (+) and ground (-), and between P/J8710 pin 3 (+) and ground (-). The voltage is approximately +24VDC. If YES, go to 22. If NO, go to 21.
21. Check the +24VDC circuit. Refer to Chapter 7 Wiring Data. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
22. Install a new rear tamper motor, PL 12.26 Item 15. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
23. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON: BSD 12.4 Integrated Office Finisher Tamping and Offset
Initial Actions
NOTE: Ensure the correct RAP is performed, refer to the 012-224, 012-263 Rear Tamper Home Sensor Fail Entry RAP.
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Check the rear tamper home sensor, PL 12.25 Item 9 is correctly installed and has no foreign object and that the actuator is not broken.
• Switch off, then switch on the machine, GP 10.
Procedure
1. Check the rear tamper for any foreign object, deformation and binding that prevents it from moving. The rear tamper is good. If YES, go to 3. If NO, go to 2.
2. Repair the deformation and remove the foreign object(s) and the binding. Install new components as necessary, PL 12.26.
3. Check the drive mechanism to the rear tamper for a deformed or broken part and not-seated gears. The drive mechanism is good. If YES, go to 5. If NO, go to 4.
4. Repair the rear tamper drive mechanism. Install new components as necessary, PL 12.26.
5. Enter dC330 code 012-221. Manually move the rear tamper to actuate the front tamper home sensor. The display of changes. If YES, go to 15. If NO, go to 6.
6. Check the connections of P/J8700 and P/J8726. The connectors are good. If YES, go to 8. If NO, go to 7.
7. Secure the connections.
8. Check for an open or short circuit between P/J8700 and P/J8726. The wiring is good. If YES, go to 10. If NO, go to 9.
9. Repair the open wire or short circuit.
10. Measure the voltage between the finisher PWB P/J8700 pin 12 (+) and ground (-). The voltage is approximately +5VDC. If YES, go to 12. If NO, go to 11.
11. Check the +5VDC circuit.
12. Measure the voltage between the finisher PWB P/J8700 pin 11 (+) and ground (-). Manually move the rear tamper to actuate the front tamper home sensor. The voltage changes. If YES, go to 14. If NO, go to 13.
13. Install a new rear tamper home sensor, PL 12.25 Item 9.
14. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
15. Enter dC330 code 012-026 and 012-029 alternately. The rear tamper motor runs. If YES, go to 23. If NO, go to 16.
16. Check the connections of P/J8710 and J8737. The connectors are good. If YES, go to 18. If NO, go to 17.
17. Secure the connections.
18. Check for an open wire or short circuit between P/J8710 and J8737. The wiring is good. If YES, go to 20. If NO, go to 19.
19. Repair the open or short circuit.
20. Measure the voltage between the finisher PWB P/J8710 pin 1 (+) and ground (-), and between P/J8710 pin 3 (+) and ground (-). The voltage is approximately +24VDC. If YES, go to 22. If NO, go to 21.
21. Check the +24VDC circuit. Refer to Chapter 7 Wiring Data. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
22. Install a new rear tamper motor, PL 12.26 Item 15. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
23. Check the wires and connectors for an intermittent open or short circuit. If the fault persists, install a new finisher PWB, PL 12.14 Item 1.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782