How to Fix 012-249 Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
012-249 Booklet Front Stapler Fail RAP
BSD-ON: BSD 13.4 Office Finisher LX Booklet Interlock Switching
BSD-ON: BSD 13.17 Office Finisher LX Booklet Staple Control (1 of 2 - Front)
012-249 The booklet front staple home switch is not on (does not return to home position) within the specified time after the booklet front staple motor starts to reverse.
Initial Actions
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
Check the booklet front stapler for jammed staples or an incorrectly installed staple cartridge.
Procedure
1. Enter dC330 code 12-024 then 12-025 to cycle the front booklet stapler. The front booklet stapler cycles normally. If YES, go to 5. If NO, go to 2.
2. Measure the voltage between P/J8993 pin 5 on the booklet PWB and ground. The voltage is approximately +24VDC. If YES, go to 4. If NO, go to 3.
3. Check the circuit from the booklet PWB to the booklet stapler cover switch. Repair the wiring or install new components as necessary, PL 13.70.
4. Switch off the machine, GP 10. Check the wiring between P/J8995 on the booklet PWB and J8894 on the front booklet stapler for a loose or damaged connector, or an open or short circuit. If the wiring is good, install a new front booklet stapler assembly, PL 13.60 Item 13. If the problem persists, install a new booklet PWB, PL 13.70 Item 4.
5. Switch off the machine, GP 10. Check the wiring between P/J8995 pin 5 on the booklet PWB and P/J8994 pin 3 on the front booklet stapler for a loose or damaged connector, or an open or short circuit. If the wiring is good, install a new front booklet stapler assembly, PL 13.60 Item 13. If the problem persists, install a new booklet PWB, PL 13.70 Item 4.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON: BSD 13.4 Office Finisher LX Booklet Interlock Switching
BSD-ON: BSD 13.17 Office Finisher LX Booklet Staple Control (1 of 2 - Front)
012-249 The booklet front staple home switch is not on (does not return to home position) within the specified time after the booklet front staple motor starts to reverse.
Initial Actions
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
Check the booklet front stapler for jammed staples or an incorrectly installed staple cartridge.
Procedure
1. Enter dC330 code 12-024 then 12-025 to cycle the front booklet stapler. The front booklet stapler cycles normally. If YES, go to 5. If NO, go to 2.
2. Measure the voltage between P/J8993 pin 5 on the booklet PWB and ground. The voltage is approximately +24VDC. If YES, go to 4. If NO, go to 3.
3. Check the circuit from the booklet PWB to the booklet stapler cover switch. Repair the wiring or install new components as necessary, PL 13.70.
4. Switch off the machine, GP 10. Check the wiring between P/J8995 on the booklet PWB and J8894 on the front booklet stapler for a loose or damaged connector, or an open or short circuit. If the wiring is good, install a new front booklet stapler assembly, PL 13.60 Item 13. If the problem persists, install a new booklet PWB, PL 13.70 Item 4.
5. Switch off the machine, GP 10. Check the wiring between P/J8995 pin 5 on the booklet PWB and P/J8994 pin 3 on the front booklet stapler for a loose or damaged connector, or an open or short circuit. If the wiring is good, install a new front booklet stapler assembly, PL 13.60 Item 13. If the problem persists, install a new booklet PWB, PL 13.70 Item 4.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782