How to Fix 012-283B 012-284B Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
012-283B, 012-284B Set Clamp Home Sensor Fail RAP
BSD-ON: BSD 13.13 Office Finisher LX Eject Control (1 of 2)
BSD-ON: BSD 13.14 Office Finisher LX Eject Control (2 of 2)
Initial Actions
NOTE: Ensure the correct RAP is performed, refer to the 012-283, 012-284 Set Clamp Home Sensor Fail Entry RAP.
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Manually operate the eject mechanism. Check for binding, a dirty sensor, or damage.
• Check the actuator for the set clamp home sensor, PL 13.27 Item 16 for damage
Procedure
1. Enter dC330 code 012-251. Actuate the set clamp home sensor. The display changes. If YES, go to 9. If NO, go to 2.
2. Check the wiring between J8871 pin 2 on the set clamp home sensor and P/J8988 pin 11 on the finisher PWB for an open or short circuit, or loose or damaged connectors. The wiring is good. If YES, go to 4. If NO, go to 3.
3. Reconnect or repair as necessary.
4. Measure the voltage between P/J8988 pins 12 and 10 on the finisher PWB. The voltage is approximately +5VDC. If YES, go to 6. If NO, go to 5.
5. Install a new finisher PWB, PL 13.45 Item 2.
6. Measure the voltage between the P/J8988 pin 11 on the finisher PWB and ground. Actuate the eject clamp home sensor. The voltage changes. If YES, go to 8. If NO, go to 7.
7. Install a new eject clamp home sensor, PL 13.27 Item 16.
8. Install a new finisher PWB,PL 13.45 Item 2.
9. Enter dC330 code 012-052 then 012-053 alternately. The eject motor, PL 13.27 Item 4 runs. If YES, go to 15. If NO, go to 10.
10. Check the wiring between P/J8878 pins 1 to 6 on the eject motor and P/J8983 pins 5 to 8 on the finisher PWB for an open or short circuit, or loose or damaged connectors. The wiring is good. If YES, go to 12. If NO, go to 11.
11. Reconnect or repair as necessary.
12. Measure the resistance of the eject motor between each pin of P/J8878-1, 3, 4 and 6. The resistance is approximately 2 Ohm. If YES, go to 14. If NO, go to 13.
13. Install a new eject motor, PL 13.27 Item 4.
14. Install a new finisher PWB, PL 13.45 Item 2. If the problem persists, install a new eject motor, PL 13.27 Item 4.
15. Enter dC330 code 012-050. The set clamp clutch energizes. If YES, go to 21. If NO, go to 16.
16. Check the wiring between P/J8877 pins 1 and 2 on the set clamp clutch and P/J8983 pins 3 and 4 on the finisher PWB for an open or short circuit, or loose or damaged connectors. The wiring is good. If YES, go to 18. If NO, go to 17.
17. Reconnect or repair as necessary.
18. Measure the voltage between the Finisher PWB P/J8983 pin 4 (+) and ground (-). The voltage is approximately +24VDC. If YES, go to 20. If NO, go to 19.
19. Install a new set clamp clutch, PL 13.27 Item 12. If the fault persists, install a new finisher PWB, PL 13.45 Item 2.
20. Install a new finisher PWB, PL 13.45 Item 2.
21. Install a new finisher PWB, PL 13.45 Item 2.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON: BSD 13.13 Office Finisher LX Eject Control (1 of 2)
BSD-ON: BSD 13.14 Office Finisher LX Eject Control (2 of 2)
Initial Actions
NOTE: Ensure the correct RAP is performed, refer to the 012-283, 012-284 Set Clamp Home Sensor Fail Entry RAP.
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Manually operate the eject mechanism. Check for binding, a dirty sensor, or damage.
• Check the actuator for the set clamp home sensor, PL 13.27 Item 16 for damage
Procedure
1. Enter dC330 code 012-251. Actuate the set clamp home sensor. The display changes. If YES, go to 9. If NO, go to 2.
2. Check the wiring between J8871 pin 2 on the set clamp home sensor and P/J8988 pin 11 on the finisher PWB for an open or short circuit, or loose or damaged connectors. The wiring is good. If YES, go to 4. If NO, go to 3.
3. Reconnect or repair as necessary.
4. Measure the voltage between P/J8988 pins 12 and 10 on the finisher PWB. The voltage is approximately +5VDC. If YES, go to 6. If NO, go to 5.
5. Install a new finisher PWB, PL 13.45 Item 2.
6. Measure the voltage between the P/J8988 pin 11 on the finisher PWB and ground. Actuate the eject clamp home sensor. The voltage changes. If YES, go to 8. If NO, go to 7.
7. Install a new eject clamp home sensor, PL 13.27 Item 16.
8. Install a new finisher PWB,PL 13.45 Item 2.
9. Enter dC330 code 012-052 then 012-053 alternately. The eject motor, PL 13.27 Item 4 runs. If YES, go to 15. If NO, go to 10.
10. Check the wiring between P/J8878 pins 1 to 6 on the eject motor and P/J8983 pins 5 to 8 on the finisher PWB for an open or short circuit, or loose or damaged connectors. The wiring is good. If YES, go to 12. If NO, go to 11.
11. Reconnect or repair as necessary.
12. Measure the resistance of the eject motor between each pin of P/J8878-1, 3, 4 and 6. The resistance is approximately 2 Ohm. If YES, go to 14. If NO, go to 13.
13. Install a new eject motor, PL 13.27 Item 4.
14. Install a new finisher PWB, PL 13.45 Item 2. If the problem persists, install a new eject motor, PL 13.27 Item 4.
15. Enter dC330 code 012-050. The set clamp clutch energizes. If YES, go to 21. If NO, go to 16.
16. Check the wiring between P/J8877 pins 1 and 2 on the set clamp clutch and P/J8983 pins 3 and 4 on the finisher PWB for an open or short circuit, or loose or damaged connectors. The wiring is good. If YES, go to 18. If NO, go to 17.
17. Reconnect or repair as necessary.
18. Measure the voltage between the Finisher PWB P/J8983 pin 4 (+) and ground (-). The voltage is approximately +24VDC. If YES, go to 20. If NO, go to 19.
19. Install a new set clamp clutch, PL 13.27 Item 12. If the fault persists, install a new finisher PWB, PL 13.45 Item 2.
20. Install a new finisher PWB, PL 13.45 Item 2.
21. Install a new finisher PWB, PL 13.45 Item 2.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782