How to Fix 058-310 to 058-321 Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
058-310 to 058-321 Fuser Checkout RAP
BSD-ON: BSD 10.2 Fusing Heat Control (1 of 2)
BSD-ON: BSD 10.3 Fusing Heat Control (2 of 2)
058-310 At warm up, the heat roll NC sensor temperature has exceeded the check temperature.
058-311 At warm up, the heat roll thermistor temperature has exceeded the check temperature.
058-318 After inspection start, the side temperature rises from the measurement start temperature to the target temperature sooner than the specified time.
058-319 The heater assessment time has arrived, the center temperature or side temperature is the setting value or less.
058-320 The side temperature does not rise to the measurement start temperature within the specified time from the inspection start.
058-321 The side temperature does not rise from the measurement start temperature to the target temperature within the specified time from the inspection start.
Initial Actions
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Remove the fuser. Check whether foreign substances or paper is wound around the heat roll.
Procedure
Perform the steps that follow:
1. Switch off, then switch on the machine, GP 10.
2. (Fault code 058-310 only) Check the heat roll NC sensor for correct installation and loose connections.
3. (Fault code 058-311 only) Check the heat roll thermistor for correct installation and loose connections.
4. (Fault code 058-319 only) Check the heater for a wiring error.
5. (Fault code 058-320 only) Check the main heater rod for open circuit or poor contact.
6. (Fault code 058-321 only) Check the sub heater rod for open circuit or poor contact.
7. Ensure that the fuser is installed correctly and is the correct voltage for the region.
8. Check the drawer connector between the fuser ( DJ612) and the main unit ( DP612) for damage.
9. Check the connections and wiring between the fuser ( DJ612) and the LVPS ( P2) for an open circuit, short circuit or poor contact.
10. Check the connections and wiring between the heat roll NC sensor ( P/J124) and the drive PWB ( P/J416) for open circuit, short circuit or poor contact.
11. If the fault persists, install new components as necessary:
• Fuser, PL 10.05 Item 2.
• LVPS, PL 1.10 Item 3.
• Drive PWB, PL 1.10 Item 3.
• ESS PWB, PL 3.10 Item 6.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
BSD-ON: BSD 10.2 Fusing Heat Control (1 of 2)
BSD-ON: BSD 10.3 Fusing Heat Control (2 of 2)
058-310 At warm up, the heat roll NC sensor temperature has exceeded the check temperature.
058-311 At warm up, the heat roll thermistor temperature has exceeded the check temperature.
058-318 After inspection start, the side temperature rises from the measurement start temperature to the target temperature sooner than the specified time.
058-319 The heater assessment time has arrived, the center temperature or side temperature is the setting value or less.
058-320 The side temperature does not rise to the measurement start temperature within the specified time from the inspection start.
058-321 The side temperature does not rise from the measurement start temperature to the target temperature within the specified time from the inspection start.
Initial Actions
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
• Remove the fuser. Check whether foreign substances or paper is wound around the heat roll.
Procedure
Perform the steps that follow:
1. Switch off, then switch on the machine, GP 10.
2. (Fault code 058-310 only) Check the heat roll NC sensor for correct installation and loose connections.
3. (Fault code 058-311 only) Check the heat roll thermistor for correct installation and loose connections.
4. (Fault code 058-319 only) Check the heater for a wiring error.
5. (Fault code 058-320 only) Check the main heater rod for open circuit or poor contact.
6. (Fault code 058-321 only) Check the sub heater rod for open circuit or poor contact.
7. Ensure that the fuser is installed correctly and is the correct voltage for the region.
8. Check the drawer connector between the fuser ( DJ612) and the main unit ( DP612) for damage.
9. Check the connections and wiring between the fuser ( DJ612) and the LVPS ( P2) for an open circuit, short circuit or poor contact.
10. Check the connections and wiring between the heat roll NC sensor ( P/J124) and the drive PWB ( P/J416) for open circuit, short circuit or poor contact.
11. If the fault persists, install new components as necessary:
• Fuser, PL 10.05 Item 2.
• LVPS, PL 1.10 Item 3.
• Drive PWB, PL 1.10 Item 3.
• ESS PWB, PL 3.10 Item 6.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782