GP 10 How to Switch Off or Switch On Xerox VersaLink C7020 C7025 C7030 C7000 Printer?
Posted by Xwk Tech on
Purpose
To show how to switch off or switch on the machine, without the loss of customer data or damage to the system hardware.
WARNING: Do not use the power button as a safety disconnect device. The power button is not a disconnect device. Disconnect the power cord from the supply to isolate the equipment.
Refer to:
• Switch Off Procedure
• Quick Restart
• Switch On Procedure
• Sleep Mode
Switch Off Procedure
CAUTION: Do not disconnect the power cord or interrupt the electricity supply before the power down is complete unless advised. The data and software can become damaged.
1. Press the Power button on the UI. The Power Down Options window will display.
2. Touch Power Off.
3. Open the front cover, PL 28.05 Item 5. Switch off the main power switch, PL 1.05 Item 3.
4. When the machine has switched off, remove the power cord PL 1.15 Item 11, from the customer’s power supply outlet.
Quick Restart
The quick restart causes the system to reset the software of the ESS PWB, the drive PWB and the UI.
1. Press the Power button on the UI. The Power Down Options window will display.
2. Select the Quick Restart button on the UI touch screen.
Switch On Procedure
1. After the machine has been switched off, wait a minimum of 2 minutes before the machine is switched on.
2. After a service call, ensure that all service tools are removed from the machine.
3. Connect the power cord from the customer’s power supply outlet to the machine. Ensure the AC bracket assembly is installed, PL 1.15 Item 4.
4. Switch on the main power switch, PL 1.05 Item 3.
5. Press the Power button on the UI.
6. The machine will perform a power on self test (POST). The POST checks that the hardware resources are available to run the operating system. If a POST fault is detected, the machine is prevented from booting. The fault is communicated via LEDs on the ESS PWB. Refer to the OF1 POST Error RAP.
Restart
Restart is selected from the Power Down window. When pressed, the machine should restart within 2 minutes.
Sleep Mode
Sleep is selected from the Power Down window. When pressed, the machine should immediately enter sleep mode.
**This procedure is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
To show how to switch off or switch on the machine, without the loss of customer data or damage to the system hardware.
WARNING: Do not use the power button as a safety disconnect device. The power button is not a disconnect device. Disconnect the power cord from the supply to isolate the equipment.
Refer to:
• Switch Off Procedure
• Quick Restart
• Switch On Procedure
• Sleep Mode
Switch Off Procedure
CAUTION: Do not disconnect the power cord or interrupt the electricity supply before the power down is complete unless advised. The data and software can become damaged.
1. Press the Power button on the UI. The Power Down Options window will display.
2. Touch Power Off.
3. Open the front cover, PL 28.05 Item 5. Switch off the main power switch, PL 1.05 Item 3.
4. When the machine has switched off, remove the power cord PL 1.15 Item 11, from the customer’s power supply outlet.
Quick Restart
The quick restart causes the system to reset the software of the ESS PWB, the drive PWB and the UI.
1. Press the Power button on the UI. The Power Down Options window will display.
2. Select the Quick Restart button on the UI touch screen.
Switch On Procedure
1. After the machine has been switched off, wait a minimum of 2 minutes before the machine is switched on.
2. After a service call, ensure that all service tools are removed from the machine.
3. Connect the power cord from the customer’s power supply outlet to the machine. Ensure the AC bracket assembly is installed, PL 1.15 Item 4.
4. Switch on the main power switch, PL 1.05 Item 3.
5. Press the Power button on the UI.
6. The machine will perform a power on self test (POST). The POST checks that the hardware resources are available to run the operating system. If a POST fault is detected, the machine is prevented from booting. The fault is communicated via LEDs on the ESS PWB. Refer to the OF1 POST Error RAP.
Restart
Restart is selected from the Power Down window. When pressed, the machine should restart within 2 minutes.
Sleep Mode
Sleep is selected from the Power Down window. When pressed, the machine should immediately enter sleep mode.
**This procedure is from Xerox Service Manual. All brand names and trademarks are their respective owner's property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
Option via the web without going into “Remote Control Panel” to restart device?